今天是: <%response.write formatdatetime(date(),1)%> 电子制作天地网站欢迎您的光临,欢迎提出宝贵意见或建议。本站信息产业部备案: 粤ICP备05114582号
 
长距离调频发射器(英文)
Long range FM transmitter

时间:2010-4-12 21:23:35 来源:互联网 作者:不详 编辑: 【关闭


关键字:长距离调频发射器

这个调频发射器,做得好的话发射距离可以达到2公里哦
The power output of most of these circuits are very low because no power amplifier stages were incorporated.
The transmitter circuit described here has an extra RF power amplifier stage, after the oscillator stage, to raise the power output to 200-250 milliwatts. With a good matching 50-ohm ground plane antenna or multi-element Yagi antenna, this transmitter can provide reasonably good signal strength up to a distance of about 2 kilometres.
The circuit built around transistor T1 (BF494) is a basic low-power variable-frequency VHF oscillator. A varicap diode circuit is included to change the frequency of the transmitter and to provide frequency modulation by audio signals. The output of the oscillator is about 50 milliwatts. Transistor T2 (2N3866) forms a VHF-class A power amplifier. It boosts the oscillator signals? power four to five times. Thus, 200-250 milliwatts of power is generated at the collector of transistor T2.
For better results, assemble the circuit on a good-quality glass epoxy board and house the transmitter inside an aluminium case. Shield the oscillator stage using an aluminium sheet.
Coil winding details are given below:
L1 - 4 turns of 20 SWG wire close wound over 8mm diameter plastic former.
L2 - 2 turns of 24 SWG wire near top end of L1.
(Note: No core (i.e. air core) is used for the above coils)
L3 - 7 turns of 24 SWG wire close wound with 4mm diameter air core.
L4 - 7 turns of 24 SWG wire-wound on a ferrite bead (as choke)
Potentiometer VR1 is used to vary the fundamental frequency whereas potentiometer VR2 is used as power control. For hum-free operation, operate the transmitter on a 12V rechargeable battery pack of 10 x 1.2-volt Ni-Cd cells. Transistor T2 must be mounted on a heat sink. Do not switch on the transmitter without a matching antenna. Adjust both trimmers (VC1 and VC2) for maximum transmission power. Adjust potentiometer VR1 to set the fundamental frequency near 100 MHz.
This transmitter should only be used for educational purposes. Regular transmission using such a transmitter without a licence is illegal in India
调频发射电路

◆相关文章◆
◆ 编辑推荐 ◆
用户:
更多评论
您要为您所发的言论的后果负责,故请各位遵纪守法并注意语言文明。60个字以内
留言:
验证码:
 
 
 

免责声明:
●本站所有内容均来自网络,以学习为目的,如果侵犯了您的利益,请来信告知,立即删除,站长邮件为"diy+dzdiy.com",请将"+"变更为"@"
●电子制作存在风险,请注意人身安全,如果您在根据本站电路进行制作过程中发生伤害,本站不负任何责任。

版权所有:www.dzdiy.com © 2001-2019 本站信息产业部备案: 粤ICP备05114582号